PAINTING ADVICE
Best Brush for Painting Skirting Boards and Trim
Updated
The best brush for skirting boards and trim is a 50 to 63 mm angled sash brush with synthetic bristles. The angled tip cuts a clean line where the skirting meets the wall. The 50 to 63 mm width suits the height of most Australian skirting and architraves. Synthetic bristles stay firm in water-based enamel, which is now the standard trim paint in Sydney homes.
Choosing the brush
| Feature | What to look for | Why it matters |
|---|---|---|
| Shape | Angled (sash) cut | Gives a sharp line along the wall and into corners |
| Width | 50 – 63 mm for skirting and architraves, 38 mm for window sashes and fine beading | Wide enough to cover a board in one pass, small enough to control |
| Bristle | Synthetic nylon/polyester blend | Holds its shape in water-based enamel. Natural bristle goes limp in water-based paint |
| Tip | Fine, flagged (split) ends | Lays paint off smoothly and reduces brush marks |
| Handle | Short or rat-tail handle | Easier to control when you’re kneeling at floor level |
Spend a bit more on the brush. A good one holds more paint, keeps a clean edge and lasts for years if you wash it properly. A cheap brush sheds bristles into the finish and leaves streaks no matter how careful you are.
Oil-based enamel is still used on some older homes. For that, a natural bristle or a blend made for oil-based paint lays off better. Clean it with mineral turpentine, not water.
Prepare skirting boards before painting
- Clean. Vacuum the floor edge, then wipe the boards with sugar soap and water. Skirting collects dust, scuff marks and floor-cleaner residue, and paint won’t stick to any of it.
- Fill. Fill nail holes and dents with a fast-drying wood filler. Run a paintable gap sealant along any gap between the top of the skirting and the wall. Smooth it with a damp finger.
- Sand. Lightly sand with 180 to 240 grit to dull the old gloss so the new paint grips. Wipe off the dust.
- Check for oil-based paint. Rub a hidden spot with a cotton bud dipped in methylated spirits. If paint comes off on the bud, it’s water-based. If it doesn’t, assume oil-based and apply an oil-to-water primer before the topcoat.
- Protect the floor. Run low-tack masking tape along the floor, pressing it firmly into timber or tiles. On carpet, push a wide paint scraper into the pile as a shield as you go.
Tape the wall side only if you aren’t confident cutting in. Experienced painters freehand that edge with the angled brush.
How to paint trim without brush marks
- Load lightly. Dip only the bottom third of the bristles and tap off the excess on the side of the tin. Don’t wipe it on the rim.
- Cut the top edge first. Hold the brush on its narrow edge with the long bristles toward the wall, and draw a steady line along the top of the skirting.
- Fill in, then lay off. Brush paint onto the face of the board, then finish with one long, light stroke along the length of the board, from wet paint into wet paint.
- Keep a wet edge. Work in sections of about a metre so you’re always joining into wet paint.
- Don’t go back. Water-based enamel starts to set within minutes. Brushing over it then drags it and leaves marks. Fix any misses on the next coat.
- Sand between coats. A quick pass with 320 grit once the first coat is dry gives a smoother second coat.
Pull the masking tape off while the last coat is still slightly soft, at a low angle, so it doesn’t lift the paint.
Which paint and finish
Use a water-based enamel in semi-gloss or gloss. Skirting boards and door frames get kicked, scuffed and wiped, so they need a harder finish than walls. Water-based enamel stays white instead of yellowing like oil-based paint, dries faster and cleans up with water. For more on sheen levels, see matte vs satin vs gloss.
When to call a painter
Skirting boards, architraves and doors take longer than most people expect. In a typical house, the trims can take as long as the walls. If you’re repainting several rooms, or the trims are oil-based and need converting, ask us for a quote. Our interior painting quotes include trims.
GOOD TO KNOW
Frequently asked questions
What is the best brush for painting skirting boards?
A 50 to 63 mm angled sash brush with synthetic (nylon and polyester) bristles. The angled tip lets you cut a clean line where the skirting meets the wall, and synthetic bristles hold their shape in the water-based enamel most Australian homes now use on trims.
Should I use a brush or a roller on skirting boards?
A brush. Skirting boards are narrow and usually profiled, so a roller can't follow the shape or get a clean line against the wall and floor. A small foam roller can lay paint on long, flat skirting quickly, but finish with a brush.
What paint should I use on skirting boards and architraves?
A water-based enamel in semi-gloss or gloss. It is hard-wearing, wipes clean, does not yellow like oil-based enamel, and cleans up with water. If your existing trims are oil-based, sand them and apply an oil-to-water primer first or the new paint may peel.
How do I avoid brush marks on trim?
Use a good synthetic brush, load only the bottom third of the bristles, apply thin coats, and finish each section with one long, light stroke along the length of the board. Don't go back over paint that has started to set. Sand lightly between coats.
How many coats do skirting boards need?
Usually two coats of enamel over sound existing paint. Bare timber or MDF needs a primer or undercoat first, and a big colour change can need a third coat.